Catalogo | >> | Macchine "Z" | >> | Conner Peripherals | >> | CP 3000 |
| ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
C P - 3 0 0 0 CONNER NO MORE PRODUCED Native| Translation ------+-----+-----+----- Form 3.5"/SLIMLINE Cylinders 1045| 980| | Capacity form/unform 42/ MB Heads 2| 5| | Seek time / track 28.0/11.0 ms Sector/track 40| 17| | Controller IDE / AT Precompensation Cache/Buffer 8 KB LOOK-AHEAD Landing Zone Data transfer rate 1.500 MB/S int Bytes/Sector 512 4.500 MB/S ext Recording method RLL 2/7 operating | non-operating -------------+-------------- Supply voltage 5/12 V Temperature *C 5 55 | -40 60 Power: sleep 0.4 W Humidity % 8 80 | 8 80 standby 0.5 W Altitude km -0.061 3.050| 12.200 idle 2.0 W Shock g 5 | 75 seek 2.8 W Rotation RPM 3557 read/write 4.2 W Acoustic dBA 40 spin-up W ECC Bit INTERNAL MTBF h 100000 Warranty Month 15 Lift/Lock/Park YES Certificates CSA,IEC380,IEC435,IEC950,U... LayoutCONNER CP3000 PRODUCT MANUAL REV. I, DECEMBER 1990 +-------------------------------------------------------+ | +-+J1 +-------+ |XX J5 | | | +-------+ |xx1 Power | | |HDA HSP CD DSP ACT | | | | |XX 40 Pin | +-+ |XX Task | |XX File | |XX | |XX Inter- | |XX face | SERIAL IN/OUT |XX | LED DRIVE |XX J2 | CAPABILITY |XX |+--1 |XX || | | 1 || | J4 |XX Power J3 |+--+ |XX +-------------------------------------------------------+ 1 (AT) Adapter Card Layout J1 1 +-------------------------XXXXXXXXX.XXXXXXXXX-------------+ |O ** 2 O | | E1 | | E2** ***E4 O | | E3 | | | | | | | | | | | | | | | | O | | | | O | +-------------+ ++ +-------+ +++++++++++++++++++++++++++++++++++++ JumpersCONNER CP3000 PRODUCT MANUAL REV. I, DECEMBER 1990 Jumper Setting Customer Options HSP, when jumpered, connects the -HOST SLV/ACT signal on the inter- C/D is the address jumper. When jumpered, the master (or C drive), is DSP, when jumpered, indicates to the master drive that a slave is The last jumper, ACT, connects the -ACTIVE signal to the -HOST As an alternative, an LED may be connected between J4, pins 1 and 2. This would provide both an open collector drive signal and a current limiting resistor connected to +5V respectively. The following table shows what the jumper setting should be for various system configurations. +--------------+--------+---------------+--------------+ |Jumper | | | | |Configuration |1 Drive |2 Drive Master |2 Drive Slave | +--------------+--------+---------------+--------------+ | ACT | J | Note 1 | Note 1 | +--------------+--------+---------------+--------------+ | C/D | J | J | NJ | +--------------+--------+---------------+--------------+ | HSP | NJ | NJ | Note 2 | +--------------+--------+---------------+--------------+ | DSP | NJ | J | NJ | +--------------+--------+---------------+--------------+ NOTE 1: NOTE 2: J3 DC Power and pin connector assignments ------------------------------------------- /------------\ pin 1 +12 V | 4 3 2 1 | pin 2 GND +------------+ pin 3 GND pin 4 + 5 V J5 DC Power and pin connector assignments ------------------------------------------- +---------+ pin 1 + 5 V | 1 2 3 | pin 2 +12 V +---------+ pin 3 GND InstallCONNER CP3000 PRODUCT MANUAL REV. I, DECEMBER 1990 Notes on installation Installation direction horizontally vertically +-----------------+ +--+ +--+ | | | +-----+ +-----+ | | | | | | | | | +-+-----------------+-+ | | | | | | +---------------------+ | | | | | | | | | | | | | | | | | | +---------------------+ | +-----+ +-----+ | +-+-----------------+-+ +--+ +--+ | | | | +-----------------+ The drive may be mounted in any attitude! Recommended Mounting Configuration Shock Tolerance Features Mechanically Isolated Mounting Points For additional vibration isolation, an external suspension system may Power Connectors Power is to be supplied at either J3 or J5, but not both. Task File Interface Connector Acoustic Noise Drive Mechanism Air Filtration System Installation of the Drive and Adapter Card 1. Remove power to the computer 2. If another hard disk controller is installed, it is necessary to prevent it from responding to the addresses 1F0-7H and 3F6-7H. It is also necessary to ensure that the controller is electrically disconnected or tri-stated from IRQ14 of the mother- board bus. This may be done either by removing the board, by electrically disconnecting the signal from the interface, or by setting the jumpers of the board to disable the hard disk controller. 3. Insert the board into any available card slot. 4. Configure the Host adapter for the correct configuration of your computer BIOS. Adapter Card Jumpers E1 and E3 always not installed E2 and E4 always installed 5. Connect power to the CP3000. 6. Run the DOS FDISK program to establish DOS partitions. Note: DOS 3.3 and below have limitations of 32 megabytes unless software utility is used to overcome this. 7. Run the DOS format programm by typing "Format C:/S". The volume may be named with the addition of the "/V". The format will be completed and the system transferred if the "/V" option was used. The system will ask for a volume name. 8. Files can then be copied to the C drive from floppy. 9. When the system is rebooted, the system should boot from the hard drive (Drive C) if the floppy is removed. FeaturesCONNER CP3000 PRODUCT MANUAL REV. I, DECEMBER, 1990 Key Features - Low power requirements enabling battery operation in portable environments - High performance rotary voice coil actuator with embedded servo system - High shock resistance - Internal air filtration system - Sealed HDA - Automatic actuator latch against inner stop upon power down - Microprocessor-controlled diagnostics routines that are auto- matically executed at start-up - Automatic error correction and retries - Block size: 512 bytes - Emulates IBM Task File and supports additional commands - Up to two drives may be daisy-chained on this interface - Translate mode (17 sectors, 5 heads, 980 cylinders) is supported - Look Ahead Read Capability - AC Hysteresis on interface - 8K buffer Seek Times +----------------------------------+--------+ |Track-to-Track msec. | 11 | +----------------------------------+--------+ | Average msec. typ. | 28 | | Average msec. max. | 50 | +----------------------------------+--------+ |Latency msec. avg. | 8.4 | +----------------------------------+--------+ Functional Description Read/Write and Control Electronics The single microprocessor-controlled circuit card provides the re- - Read/Write Circuitry - Rotary Actuator Control - Interface Control - Spin Speed Control - Dynamic Braking - Power Management At power down or the starts of STANDBY MODE, the heads are Head Positioning Mechanism Read/Write Heads and Disks Error Correction Diagnostic Routines Reliability and Maintenance Execute Drive Diagnostic - 90 The drive sets BSY immediately upon receipt of this command. If the If the slave does not successfully complete its diagnostics, it sets The table below details the codes in the error register and a corresponding explanation: +----------+-----------------------------------+ |Error Code|Description | +----------+-----------------------------------+ | 01 |no error detected | | 03 |sector buffer error | | 8x |slave drive failed (see note below)| +----------+-----------------------------------+ NOTE Error Reporting +-----------------+---+---+----+----+---+----+---+---+----+---+ |Commands |BBK|UNC|IDNF|ABRT|TK0|DRDY|DWF|DSC|CORR|ERR| +-----------------+---+---+----+----+---+----+---+---+----+---+ |Recalibrate | | | | V | V | V | V | V | | V | |Read Sector | V | V | V | V | | V | V | V | V | V | |Read Sec. Long | V | | V | V | | V | V | V | | V | |Write Sector | V | | V | V | | V | V | V | | V | |Write Sec. Long | V | | V | V | | V | V | V | | V | |Read Verify Sec. | V | V | V | V | | V | V | V | V | V | |Format Track | | | V | V | | V | V | V | | V | |Seek | | | V | V | | V | V | V | | V | |Exec. Drive Diag.| | | | V | | | | | | V | |Initi. Parameters| | | | V | | | | | | V | |Read Buffer | | | | V | | | | | | V | |Write Buffer | | | | V | | | | | | V | |Identify Drive | | | | V | | | | | | V | |Inval.Cmnd. Codes| | | | V | | | | | | V | |Look Ahead Read | | | | V | | | | | | V | +-----------------+---+---+----+----+---+----+---+---+----+---+ Key: Signal Levels Share and EnjoyTags
|